devices.esphome.io

Deta Grid Connect Smart Double Touch Power Point

Deta Grid Connect Smart Double Touch Power Point

Device Type: plug
Electrical Standard: au
Board: esp8266

Deta Grid Connect Smart Double Touch Power Point

Sold by Bunnings Warehouse this is a AU/NZ standard wall outlet/powerpoint based on the TYWE3S module.

Getting it up and running

tuya-convert

These outlets are Tuya devices, so if you don't want to open them up to flash directly, you can attempt to use tuya-convert to initially get ESPHome onto them however recently purchased devices are no longer Tuya-Convert compatible. There's useful guide to disassemble and serial flash similar switches here. After that, you can use ESPHome's OTA functionality to make any further changes.

  • Put the outlet into "smartconfig" / "autoconfig" / pairing mode by holding any button for about 5 seconds.
  • The status LED (to the side of the button(s)) blinks rapidly to confirm that it has entered pairing mode.

direct flashing

If you can't or don't wish to use tuya-convert, you can flash directly to the outlet with USB to serial adapter.

To disassemble the outlet in order to flash, remove the front plastic face (secured by clips on each side), then remove the two exposed screws. Remove the clear panel and then carefully remove the small thin PCB that sat underneath the panel.

Note that the side of the TYWE3S module where the 3v3 pin is located may be covered in silicone / epoxy. You may be able to simply dig at it enough that the 3v3 pin is accessible.

GPIO pinout

GPIO #Component
GPIO00None
GPIO01None
GPIO02None
GPIO03None
GPIO04Status LED
GPIO05None
GPIO09None
GPIO10None
GPIO12Button 2n
GPIO13Relay 1
GPIO14Relay 2
GPIO15None
GPIO16Button 1n

Basic Configuration

substitutions:
  device_name: deta_double_powerpoint
  friendly_name: "Deta Double Powerpoint"
  
#################################


esphome:
  name: ${device_name}


esp8266:
  board: esp01_1m
  restore_from_flash: true


wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password
  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "ESPHOME"
    password: "12345678"


api:
  encryption:
    key: !secret api_encryption_key


ota:
  password: !secret ota_password


logger:


web_server:
  port: 80


sensor:
  - platform: uptime
    name: ${device_name} Uptime


  - platform: wifi_signal
    name: ${device_name} Wifi Signal
    update_interval: 60s


text_sensor:  
  - platform: version
    name: ${device_name} ESPhome Version
  - platform: wifi_info
    ip_address:
      name: ${device_name} IP


#################################


status_led:
  pin:
    number: GPIO04
    inverted: false


binary_sensor:
  - platform: gpio
    pin:
      number: GPIO16
      inverted: True
    id: button1
    name: "${device_name} Button 1"
    on_click:
      - min_length: 300ms
        max_length: 1000ms
        then:
          - switch.toggle: relay_template1
    internal: True
  - platform: gpio
    pin:
      number: GPIO12
      inverted: True
    id: button2
    name: "${device_name} Button 2"
    on_click:
      - min_length: 300ms
        max_length: 1000ms
        then:
          - switch.toggle: relay_template2
    internal: True


switch:
  - platform: gpio
    pin: GPIO13
    id: relay1


  - platform: gpio
    pin: GPIO14
    id: relay2


  - platform: template
    name: ${device_name} Socket A
    id: relay_template1
    lambda: |-
      if (id(relay1).state) {
        return true;
      } else {
        return false;
      }
    turn_on_action:
      - switch.turn_on: relay1
    turn_off_action:
      - switch.turn_off: relay1


  - platform: template
    name: ${device_name} Socket B
    id: relay_template2
    lambda: |-
      if (id(relay2).state) {
        return true;
      } else {
        return false;
      }
    turn_on_action:
      - switch.turn_on: relay2
    turn_off_action:
      - switch.turn_off: relay2
Edit this page on GitHub

On this page